思科交換機的基本配置
隨著Internet的高速發展,網絡規模不斷膨脹,對于從事網絡專業的學生熟練掌握路由器和交換機的配置已顯得十分重要。接下來是小編為大家收集的思科交換機的基本配置方法，希望能幫到大家。
思科交換機的基本配置的方法
一、交換機的基本配置
Author：chenchao in ZJNU
從本篇文章開始，將連載大概8-9篇自己學習交換與路由的實驗報告，但是怕自己能力不行，會出現錯誤，所以，先載兩篇文章，依次為：交換機的基本配置;路由器基本配置。本篇為交換機的基本配置，使用的仿真軟件是Cisco的一款免費軟件：Cisco Packet Tracer。想學習的可以在百度自行下載。
下面開始附上實驗過程：
實驗環境：
Cisco 2950交換機1臺，Console電纜1根，PC機一臺，網線1根。連接如下圖所示：
實驗步驟：
一、 交換機的帶外配置;
1、 在用戶模式、特權模式、全局模式、接口模式之間轉換;
Switch>enable
Switch#configure terminal
Enter configuration commands, one perline. End with CNTL/Z.
Switch(config)#interface FastEthernet 0/1
Switch(config-if)#exit
Switch(config)#exit
Switch#
%SYS-5-CONFIG_I: Configured from console byconsole
Switch#exit
Switch con0 is now available
Press RETURN to get started.
Switch>
2、將交換機的名稱改為“student”;
Switch(config)#hostname student
student(config)#
3、 為交換機各個模式設置密碼“cisco”;
特權模式下的密碼保護
student#enable
student#configure t
Enter configuration commands, one perline. End with CNTL/Z.
student(config)#enable password cisco
student(config)#enable secret cisco1
遠程登錄口令設置
student#configure t
Enter configuration commands, one perline. End with CNTL/Z.
student(config)#line console 0
student(config-line)#line vty 0 4
student(config-line)#password cisco2
student(config-line)#login
student(config-line)#
student#
4、為交換機制定一個IP地址10.10.10.X/24;
student#config
Configuring from terminal, memory, ornetwork [terminal]?
Enter configuration commands, one perline. End with CNTL/Z.
student(config)#interface vlan 1
student(config-if)#ip address 10.10.10.1255.0.0.0
5、開啟交換機的Telnet服務功能，建立Telnet用戶admin，口令cisco，并制定只能從10.10.10.y/24登錄Telnet服務器;
student#
student#configure t
Enter configuration commands, one perline. End with CNTL/Z.
student(config)#user admin password 0 cisco
student(config)#
6、 查看配置情況;
student>enable
Password:
student#show running-c
Building configuration...
hostname student
!
enable secret 5 class="main">
思科交換機的基本配置
enable password cisco
!
!
username admin password 0 cisco
interface Vlan1
ipaddress 10.10.10.1 255.0.0.0
!
!
line con 0
!
line vty 0 4
password cisco2
login
line vty 5 15
login
!
!
End
二、交換機的端口配置：
1、 配置接口的描述、關閉借口、啟動接口、配置接口的速度為100Mbps、配置接口工作模式為全雙工、配置接口的流程控制;
student#configure terminal
Enter configuration commands, one perline. End with CNTL/Z.
student(config)#interface FastEthernet0/1
student(config-if)#shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1,changed state to administratively down
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol onInterface Vlan1, changed state to down
student(config-if)#
student(config-if)#exit
student(config)#interface FastEthernet0/1
student(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/1,changed state to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface Vlan1, changed state to up
student(config-if)#speed 100
student(config-if)#duplex full
%LINK-5-CHANGED: Interface FastEthernet0/1,changed state to down
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol onInterface Vlan1, changed state to down
student(config-if)#
2、 配置接口FastEthernet0/10為Access口;
student#
student#configure terminal
Enter configuration commands, one perline. End with CNTL/Z.
student(config)#interface FastEthernet0/10
student(config-if)#switchport mode access
student(config-if)#
3、 配置接口FastEthernet0/12為Trunk口;
student#
student#configure t
Enter configuration commands, one perline. End with CNTL/Z.
student(config)#interface fastethernet0/12
student(config-if)#switchport mode Trunk
student(config-if)#end
4、 查看配置情況;
!
interface FastEthernet0/1
duplex full
speed100
!
interface FastEthernet0/2
!
interface FastEthernet0/9
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
!
interface FastEthernet0/12
switchport mode trunk
!
student#show running-c
Building configuration...
Current configuration : 1275 bytes
!
version 12.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname student
!
enable secret 5 class="main">
思科交換機的基本配置
enable password cisco
!
!
username admin password 0 cisco
!
!
interface FastEthernet0/1
duplex full
speed 100
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
!
interface FastEthernet0/12
switchport mode trunk
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet1/1
!
interface GigabitEthernet1/2
!
interface Vlan1
ipaddress 10.10.10.1 255.0.0.0
!
!
line con 0
!
line vty 0 4
password cisco2
login
line vty 5 15
login
!
!
end
看了“思科交換機的基本配置”還想看：
熱門文章
-
cisco思科交換機故障Flash空間不足怎么解決
網吧專用交換機有哪些常見的故障怎么解決
華為交換機的RRPP配置實驗步驟教程
CISCO三層交換機怎么配置DHCP功能
思科交換機怎么查看任意接口的配置信息
H3C交換機什么方法可以完全刪除H3C交換機VLAN
思科交換機如何實現在一次添加多個端口
交換機怎么配置RSTP協議用到什么命令
思科交換機的端口聚合口怎么配置
cisco三層交換機怎么實現vlan間的通訊命令教程